XTOOL EZ400 PRO Diagnostic Tool Wireless Diagnosis Via Bluetooth Remote Access

  

International Buyers - Please Note. Instead of sending back directly without permission.

MicroUSBBattery charge or data synchronization with PC 2. DB15 PortSupports wired connection with car by the cable 3. Power Button: Power on or power off EZ400 PRO Technical Parameters Operating System: Android ProcessorQuad-core 1.6GHz Processor Memory: 1G RAM16G FLASH Display: 7.0 inch touch screen with 1024×600 resolution Sensors: Gravity SensorAmbient Light Sensor Audio Input/Output: Microphone, Dual Speakers, 4-Band 3.5 mm stereo/standard headset jack Power and Battery: 4000mAh, 3.7V lithium-polymer battery Power Voltage: 5V Power Consumption: 8W Operating Temperature: -20 to 50(-4 to 126) Humidity. Connect cables and EZ400PRO in following order.

Switch on the ignition and turn on EZ400 PRO tablet, then tap on EZ400 PRO application to test vehicles. Vehicle Precautions Before Use 1.

The vehicle power supply has to meet the normal voltage limits DC4.8V---5V. When pull and plug test wire harness, users should pinch the front-end of the wire harness to pull and plug, not pull the middle section of the wire harness. Users should check the corresponding direction of the port and plug in horizontally when they plug the wire harness, instead of inserting in an oblique way, which may damage the terminal. When taking some special functions tests, users are required to operate the device according to operating instructions. For vehicle, it has to strictly meet the requirements, for example, the conditions that some vehicle models need to be reached are as follows: engine temperature 80/105, turn off the loads such as headlights, air-conditioner, etc.

, put accelerator pedal in released position, etc. The ECU for Chinese domestic vehicle models are relatively disorderly, so when users meet conditions, such as the car can not be tested or the test data is wrong, they should consider whether the selected menu corresponds to the tested electronic control system, or they can find the car ECU and select the right menu according to the model number on the ECU label. If users can not find the tested vehicle model or electronic control system in EZ400PRO test menu, they may need to update the software or consult Xtool technical service department 6. Banned to have connection test by using harness not from Xtool to avoid unnecessary losses. Banned to power off directly in the communication between EZ400PRO and vehicle.

Users should cancel the task and return to the main interface, then power off. The device should be put and lifted slightly to avoid collision when using EZ400PRO. During long period of non-use, please disconnect the power and turn it off.

After EZ400PRO tablet connected to vehicle via main cable, diagnosis can be performed now. The diagnostic interface comes up as below. Users can choose menu based on their actual needs: selection for Europe means entering European cars menu, selection for Asia means entering Asian cars menu, selection for America means entering American cars menu, selection for China means entering Chinese cars menu. Users also can input vehicle model to search. Test Functions Take Volkswagen car for example, select Diagnosis, then select Europe Car, users can see Volkswagen's logo. If the logo has not been seen, please swipe up and down or enter the car model to research. Different vehicles have slight different menus. Common main function menu includes the following options: Read ECU This function is to read ECU version information, which is the equivalent of "System Identification" or "System Information" in some electronic control systems, all mean to read ECU related software and hardware versions, shown as below.

Read DTCs Select Read Trouble Codes to read trouble codes stored in ECU. Screen will show the trouble code and its definition when read the trouble codes, shown as below. Tip: In the process of diagnosis, if the device shows "System is OK" or "No Trouble Code", it means there is no related trouble code stored in ECU or some troubles are not under the control of ECU, most of these troubles are mechanical system troubles or executive circuit troubles, it is also possible that signal of the sensor may bias within limits, which can be judged in Live Data.

Clear DTCs Return to the previous step, select Clear DTCs to clear current and historical trouble codes memory in ECU. Performing this function will clear all the current and historical trouble codes.

Make sure whether the trouble codes have been recorded before clearing, shown as below. Generally, users need re-read trouble codes after cleaning them to confirm whether the trouble codes have been cleared.

Read Live Data Auto ECUs send out operating parameters and working status of various components in the form of Electronic Signal, here Electronic Signal refers to Live Data. Common Engine Live Data includes Engine Speed, Throttle Position Sensor Voltage, Oxygen Sensor Voltage, Coolant Temperature, Spark Advance Angle, Idle Speed Switch State, Intake Air Temperature, Intake Pressure, etc. Tips: Live Data is the important function for maintenance technicians to further diagnose the troubles. This function needs maintenance technicians very familiar with sensor data of each system, control signals and control modes, all which are the indispensable basis of using Live Data function for maintenance technicians.

Display Modes There are two modes to view Live Data, users can choose optimum mode according their own needs and different parameter types. Dashboard Mode: Display parameters in the form of simulating instrument graphics. Graph Mode: Display parameters in the form of graph.

Special Functions More special function will be found in different vehicle models. Test Conditions: Ignition on engine off If engine started or rotation speed signal recognized, actuating component diagnosing will be interrupted. In the process of actuating components diagnosis, single component will always be in the trigger status until the next component being activated. Before repeating actuating components diagnosis, users should start engine in short-time, or turn ignition off for 2 seconds.

Actuating components can be checked by hearing or touching. In the process of all actuating components diagnosis, electric fuel pump is always working. 10 minutes later, actuating components diagnosing is terminated. Actuating Component: it is responsible for executing various instructions issued by ECU, which is the instruction completer. Return to Dynamic Diagnostic Data , enter Actuating Components Test and it will show the menu of the actuating components that carry out action test, shown as below.

Tip: Actuating Components Test performs function tests for parts of system actuating components. When performing this function, the diagnostic tool will take action test by simulating ECU signal to judge whether the actuating components or circuits are good. Return to Dynamic Diagnostic Data, enter Actuating Components Test and it will show the menu of the actuating components that carry out action test. Settings Select enter Settings; users can set the language, unit and other system related options: Languages: select the language. Please tick the needed option from multi-language options on the right.

Units: Select unit of measurement. Users can tick Metric or English measurement.

System Settings: Android system setup, such as wireless, audio frequency, light sensation, etc. Package List: 1pc x OBD II-16 1pc x. HONDA-3 1pc x for BMW-20 1pc x. BENZ-14 1pc x MAINCABLE 1pc x Battery Cable 1pc x Cigar Lighter Cable 1pc x EZ400PRO Tablet 1pc x Charger for Tablet 1pc x Charger US Adapter 1pc x Charger EU Adapter 1pc x MicroUSB Cable 1pc x Tool Case 1pc x Certificate of Quality 1pc x Packing List 1pc x User Manual 1pc x Carton. Most of our items have.

We will do our best to solve the problem for you as soon as possible. We don't responsible for any custom duty or import cost. Please tell us the value/name of the item you want for custom delaration if you have any special requirement, or we will fill the custom.

Declaration which is suitable for most countries accordingly. Sorry for delay reply on weekend. Welcome to visit my store. The item "XTOOL EZ400 PRO Diagnostic Tool Wireless Diagnosis Via Bluetooth Remote Access" is in sale since Sunday, November 15, 2020.

This item is in the category "eBay Motors\Automotive Tools & Supplies\Diagnostic Service Tools\Other Diagnostic Service Tools". The seller is "carobdtool88" and is located in Monroe Township, New Jersey. This item can be shipped to United States.

1. Brand: XTOOL
2. Country/Region of Manufacture: China
3. Custom Bundle: No
4. Feature1: One-click software update via WIFI/Remote access
5. Feature2: Easy registration with EZ400 PRO connected to WIFI
6. Feature3: 7 inch multi-touch screen/On-board battery
7. Feature4: Diagnosis reports in PDF file /Record and playback live data
8. FLASH Display: 7.0 inch touch screen with 1024×600 resolution
9. Humidity: <90% Dimension (L*W*H): 218*150*29mm
10. Item Type: Code Reader Scanner
11. Manufacturer Part Number: K001USSP254-C
12. Model: EZ400 Pro
13. Modified Item: No
14. Non-Domestic Product: No
15. OBD Interface: EOBD
16. Operating System: Android
17. Operating Temperature: -20 to 50(-4 to 126)
18. Power and Battery: 4000mAh, 3.7V lithium-polymer battery
19. Power Consumption: 8W
20. Power Voltage: 5V
21. Processor: Quad-core 1.6GHz
22. Processor Memory: 1G RAM,16G
23. Sensors: Gravity Sensorm, Ambient Light Sensor
24. Type: Auto Diagnostic Tool
25. Vehicle Type: Passenger Vehicle
26. Warranty: 1 Year